ASTM Ea, Standard Practice for Use of the International System of Units. ISO , SI Units and Recommendations for the Use of Their Multiples. ASTM E [ Withdrawn ]. Standard for Metric Practice. standard by ASTM International, 01/01/ View all product details. Most Recent. Find the most up-to-date version of ASTM E at Engineering

Author: Fekinos Goltikora
Country: Mali
Language: English (Spanish)
Genre: Travel
Published (Last): 22 April 2006
Pages: 182
PDF File Size: 19.9 Mb
ePub File Size: 13.24 Mb
ISBN: 985-1-97858-621-5
Downloads: 72499
Price: Free* [*Free Regsitration Required]
Uploader: Vijinn

If a particular type or grade ee380 material lends itself to the fabrication desired, it should be specified. This method is suitable for use in specifications and regulatory statutes. Search Drafting Zone Resources.

Definitions from the Florida Building Code, Building shall take precedence. The stand shall be adjustable to setting the test panel at any desired slope, at any horizontal distance from the awtm edge of the duct opening, and at various angles incident to the wind direction.

Standard for Metric Practice – ASTM E

It also facilitates soldering and antigalling. However, if the use of a trade name is necessary, include the name of the ve. This method, assisted by experience and engineering judgment, will also prove useful for development work.

Secure the shingles at the outer edge of the test panel by exposed nailing to simulate anchoring at the rake edges of a roof deck. Avoid the use of asfm names for the specification of materials. Also known as hot strength.

This effort is entering its third year. The cell or room shall be capable of receiving a minimum 50 in. The fourteen remaining items of controversy were resolved and the new document could have been issued in The service condition designation is for protection against wett. The test incline shall be 2: If the project engineer should require other service conditions, they should be specified in accordance with ASTM standards, as noted above.


Plastics suitable for plating are acrylonitrile, butadiene, styrene, polypropylene, and polysulfone. No aetm, other than the factory-applied adhesive, shall be used to fasten down the tabs. Hot-dipped – Has an. These materials are manufactured by various companies and may be known as various trademark products.

This standard does not purport to address all of the safety problems associated with its use. The target course shall be the third course up axtm the bottom of the test specimen.

There was a problem providing the content you requested

No undercoating is required on steel substrates. However, you may download material from The Drafting ZONE awtm the Web one machine readable copy and one print copy per page for your personal, noncommercial use only.

All materials contained on this site are protected by United States copyright law and may not be reproduced, distributed, transmitted, displayed, published or broadcast without the prior written permission of Genium Group, Inc.

Do not apply pressure to the shingle tabs either during or after application.

Modern Metric Conversion Factors Table | Metropolitan Aircraft Parts Inc. ()

Inspection of parts should be in accordance with ASTM standards. Full details are available upon request from Genium Publishing Corporation. The wood test deck shall be of such rigidity that it will s380 twist or distort with normal handling, or vibrate from the wind velocity during the test.


An example of this would be SAESteel. Dual dimensioning practices are also to be discouraged for commercial applications in new design. When specifying special materials, furnish a more complete description to facilitate procurement and incoming inspection. You may not alter or remove any trademark, copyright or other notice from copies of the content. Local wind conditions may differ from the test conditions both in intensity and duration, and should be taken into consideration.

Test another panel at the position judged to be most critical on the basis of the first three tests.

In addition, no free portion of a shingle or non-rigid component shall lift so as to stand upright or bend back on itself during the test. The end point for failure shall be taken as the time at which the sealing feature fails to restrain one or more full shingle tabs, or a locking ear or tab of a lock shingle tears loose or disengages from its locking position or a non-rigid component is damaged so as to affect the performance of the system.

It is the responsibility of the user to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Enter one or more keywords separated by spaces.